Subcomité | Título de subcomité | Normas publicadas | Normas en desarrollo |
---|---|---|---|
ISO/TC 60/SC 1 | Nomenclature and wormgearing | 12 | 1 |
ISO/TC 60/SC 2 | Gear capacity calculation | 28 | 3 |
Filtrar :
Norma o proyecto bajo la responsabilidad directa de ISO/TC 60 Secretaría | Etapa | ICS |
---|---|---|
Cylindrical gears for general and heavy engineering — Basic rack
|
95.99 | |
Cylindrical gears for general and heavy engineering — Standard basic rack tooth profile
|
90.93 | |
Cylindrical gears for general engineering and for heavy engineering — Modules and diametral pitches
|
95.99 | |
Cylindrical gears for general engineering and for heavy engineering — Modules
|
90.93 | |
Withdrawal of ISO/R 467-1966
|
95.99 | |
Straight bevel gears for general engineering and heavy engineering — Basic rack
|
90.93 | |
Straight bevel gears for general engineering and heavy engineering — Modules and diametral pitches
|
90.93 | |
International gear notation — Symbols for geometrical data
|
95.99 | |
Glossary of gear terms — Part 1: Geometrical definitions
|
95.99 | |
Withdrawal of ISO/R 1122-1969
|
95.99 | |
Cylindrical gears — ISO system of accuracy — Part 1: Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
|
95.99 | |
Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth
|
90.60 | |
Cylindrical gears — ISO system of accuracy — Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information
|
95.99 | |
Cylindrical gears — ISO system of flank tolerance classification — Part 2: Definitions and allowable values of double flank radial composite deviations
|
60.60 | |
Parallel involute gears — ISO system of accuracy
|
95.99 | |
Cylindrical gears — Information to be given to the manufacturer by the purchaser in order to obtain the gear required
|
95.99 | |
Straight bevel gears — Information to be given to the manufacturer by the purchaser in order to obtain the gear required
|
95.99 | |
Single-start solid (monobloc) gear hobs with axial keyway, 1 to 20 module and 1 to 20 diametral pitch — Nominal dimensions
|
95.99 | |
Single-start solid (monobloc) gear hobs with tenon drive or axial keyway, 1 to 40 module — Nominal dimensions
|
95.99 | |
Addendum modification of the teeth of cylindrical gears for speed-reducing and speed-increasing gear pairs
|
95.99 | |
Gear hobs — Single start — Accuracy requirements
|
95.99 | |
Acceptance code for gears — Part 1: Determination of airborne sound power levels emitted by gear units
|
95.99 | |
Acceptance code for gear units — Part 1: Test code for airborne sound
|
90.60 | |
Acceptance code for gears — Part 2: Determination of mechanical vibrations of gear units during acceptance testing
|
95.99 | |
Code of inspection practice — Part 1: Inspection of corresponding flanks of gear teeth
|
95.99 | |
Code of inspection practice — Part 1: Inspection of corresponding flanks of gear teeth — Technical Corrigendum 1
|
95.99 | |
Code of inspection practice — Part 1: Measurement of cylindrical gear tooth flanks
|
95.99 | |
Code of inspection practice — Part 1: Measurement of cylindrical gear tooth flanks
|
90.93 | |
Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash
|
90.92 | |
Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash — Technical Corrigendum 1
|
60.60 | |
Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash — Technical Corrigendum 2
|
60.60 | |
Code of inspection practice — Part 2: Double Flank Radial Composite Measurements
|
30.99 | |
Code of inspection practice — Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes
|
90.93 | |
Code of inspection practice — Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes — Technical Corrigendum 1
|
60.60 | |
Code of inspection practice — Part 4: Recommendations relative to surface texture and tooth contact pattern checking
|
90.93 | |
Code of inspection practice — Part 4: Recommendations relative to surface texture and tooth contact pattern checking — Technical Corrigendum 1
|
60.60 | |
Code of inspection practice — Part 5: Recommendations relative to evaluation of gear measuring instruments
|
90.93 | |
Code of inspection practice — Part 5: Recommendations relative to evaluation of gear measuring instruments — Technical Corrigendum 1
|
60.60 | |
Code of inspection practice — Part 6: Bevel gear measurement methods
|
90.93 | |
Enclosed gear drives for industrial applications
|
95.99 | |
Enclosed gear drives for industrial applications — Technical Corrigendum 1
|
95.99 | |
Bevel gears — ISO system of accuracy
|
90.93 | |
Gears — Evaluation of instruments for the measurement of individual gears
|
90.93 | |
Cylindrical involute gears and gear pairs — Part 2: Calculation and measurement of tooth thickness and backlash
|
40.60 | |
Wind turbines — Part 4: Design requirements for wind turbine gearboxes
|
90.92 | |
Wind energy generation systems — Part 4: Design requirements for wind turbine gearboxes
|
60.00 | |
Wind energy generation systems — Part 4-2: Lubrication of drivetrain components in wind turbines
|
30.99 | |
Wind energy generation systems — Part 4-3: Explanatory notes on IEC 61400-4 - Supportive information for wind turbine gearbox design
|
30.99 | |
Wind energy generation systems — Part 4-1: Reliability assessment of drivetrain components in wind turbines
|
60.00 | |
Wind turbines — Part 4: Design and specification of gearboxes
|
95.99 | |
Wind turbines — Part 4: Design and specification of gearboxes — Technical Corrigendum 1
|
95.99 |
No se ha encontrado ningún registro que coincida. Pruebe a cambiar los ajustes de filtro.